PDA

View Full Version : Exhaust



Pages : 1 [2]

  1. 84 Downpipe and Cat question
  2. exhaust tips
  3. CAT OR NO CAT, DIFFERENCE? short story.
  4. Over Axle pipes
  5. dual tips on 84..
  6. exhaust drone
  7. E3/E6 exhaust manifolds
  8. Down pipe
  9. Remflex Exhaust Manifold Gasket
  10. where to get stock size chrome tailpipes
  11. Turbo removal/tightening questions...
  12. Stock turbo trim
  13. aero chambers
  14. Stock Replacement full exhaust
  15. Flomaster catback Question
  16. Looking for 3" '85 Style Tips
  17. Rod's Headers
  18. Wastgate Heat Shield
  19. Correct Catalytic converter?
  20. header
  21. Leak just after turbo elbow
  22. turbo removal
  23. Gasket woes
  24. Stinger Exhaust?
  25. Motion Dynamics 3" down pipe has serious issues
  26. 1984 Cat
  27. Mandrel Bending in Atlanta for custom FMIC?
  28. Just finished the exhaust!
  29. 3" exhaust system
  30. Pics of my setup
  31. 3" elbow
  32. 3" exhaust pics w/IRS
  33. problems installing midpipes to downpipe
  34. Update: 3" Downpipe Installed
  35. Engine started to whistle loudly
  36. 3" Downpipe... Best for the money?
  37. rf-e6
  38. Cracked turbo housing
  39. '84 Exhaust - fuel pump interference...
  40. had my own little project going on
  41. manifold cracks..
  42. hot side size..
  43. Having problems with new exhaust
  44. Cheap exhaust options?
  45. no tailpipe?
  46. Got Borla's and fixed my exhaust bump noise
  47. Flowmaster exhaust pipe
  48. 3" to 2.5" Opinion needed
  49. dual piped w/NO mufflers
  50. magnaflow or flowmaster?
  51. Flex Bellows
  52. 3" borla xr-1 clip
  53. whats a good choice?
  54. motion-dynamics DP cracked!
  55. no cat?
  56. T3 Turbine Question
  57. Failed Smog High CO levels.
  58. Merkur Depot Downpipe
  59. Tail Pipe Install Help
  60. Call me old, but...
  61. 85.5 SVO Mufflers
  62. .60 compressor wheel
  63. Replacement 84 Exhaust Tip
  64. Exhaust Manifold Bolts
  65. What's needed to put dual exhaust on an '84?
  66. leak at elbow to downpipe
  67. which manifold bolts get sealant?
  68. EGR tube Elimination Question
  69. SCE copper exhaust gasket
  70. .48 Turbo
  71. How's my turbo look?
  72. FMIC install
  73. 3'' downpipe ?
  74. California Catalytic Converter
  75. New Exhaust Today
  76. Machining Manifold
  77. What should I do?!
  78. Turbo Y bracket
  79. separate turbo hot side
  80. Downpipe installation
  81. Flex pipe?
  82. Straight pipe? Need opinions ASAP!!!
  83. Exhaust with Torque arm and Panhard??
  84. Looking for opinions..
  85. External wastegate benefits?
  86. Full 3 inch Single Exhaust
  87. what's correct
  88. 86 SVO catback exhaust.
  89. Hollowing the cat ???
  90. Borla Cat Back
  91. Does anyone make a decent cat-back for our SVO's?
  92. Leak test?
  93. Exhaust Manifold Gasket R/R
  94. Replacement 84 Muffler
  95. Full exhaust system, and a few other mods
  96. Turbo elbow to downpipe bolt size?
  97. local shop DP vs pre-made question
  98. Ported my E6 manifold...Any opinions?
  99. not as loud anymore :-)
  100. Single 2.5 tail pipe #number
  101. Stock Sounding Muffler
  102. Oil on exhaust bolts
  103. External Wastegate
  104. snapped the c clip
  105. Fitment Issues with 3" Downpipe
  106. 86 SVO turbo down elbow
  107. Stinger exhaust
  108. catalytic converter removed
  109. Turbo to exhaust manifold studs and nuts
  110. SpinTech-What part number?
  111. SS Header
  112. Anyone recognize this header???
  113. Tail pipe
  114. Any Tubular headers for stock location still available?
  115. Ported E6 worth the money?
  116. E6 with a crack, ok or no?
  117. Exhaust manifold install help
  118. Value of exhausts...
  119. Is anyone still making a 3" downpipe?
  120. 5 bolt exhaust flange
  121. So is the general consensus to install a flex section after the downpipe?
  122. turbo down pipe
  123. Turbo Manifold
  124. Porting the E3 Manifold