Will these Wheels fit my SVO?

[svoson]

Thanks, Eric. I PM'd you on this.

[onequickgt]

ROH WHEELS

Has anyone tryed to put a 17x8.5 roh zs wheel on the front of a SVO.. I have a 87GT with 84-86 Svo rotors on the front.. I am wondering if I can bolt a set of 5-lug roh zs wheels on it.. The wheels were on a 95 GT..Will they fit no dust cap problem??

[under pressure]

I decided on the LX Mustang wheels like those on The Road Warrior. What years LX 5 spoke 16 in. flat alumn. wheels fit?

[under pressure]

The 94-98 LX wheels fit. I really like the Bullit wheels they fit and look great on Matt's restored SVO. I don't know what the offset is in comparision to the stock SVO wheels. I also like the looks of the new Mustang wheels but again I'm not sure of the offset and they may be 17 inch. The wheels get rolling.

[CFARRELL]

Does anyone know what the Mach 1 wheels look like on an SVO and do they fit?

[indiana dave]

I tried some amatuer photoshopping of some Mach 1's on mine, but they didn't look as good as I thought they would. I can't find the picture. Here's one of the new Halibrand style wheels on mine. As bad as the photo editing is, I still like it with those.

[five0h2go]

Does anyone know what the Mach 1 wheels look like on an SVO and do they fit?

Here's a pic of the car i bought today. Didn't get it home yet. The wheels fit but at the stock ride height they rub a bit in the rear over big bumps. Prior owner installed 1 in spacers in the rear and now it doesn't hit any more. I may roll the rear fenders and bring the car back down again in time!

[Eyelawdoc]

Looks good! I hadn't seen an SVO with 03 Mach 1 wheels before. Are the front suspension and hubs/rotors stock?

[five0h2go]

Looks good! I hadn't seen an SVO with 03 Mach 1 wheels before. Are the front suspension and hubs/rotors stock?

Thanks for the compliment! I like the look too, and I'm going to figure something out to keep them and make it right at the same time. I think I might have a shot with lower profile tires. Going to research that now. The front suspension is stock. Tomorrow night and it'll be in my driveway!

[Gator]

Just a reminder....

When shopping for aftermarlet rims always always always get the inside bore diameter of the hub ( ie: hub spacing ) especially if you are going to use your stock brake rotors.

ALOT of aftermarlet rims will not fit. Now that doesnt mean you cant have the centers machined to fit, but if you do that take into consideration the center cap.

I believe the last time i checked the diam of the hub was something like 2.75in or 2.79 something like that.

[TheViking]

Hey Dominic,

Good to see another SVO owner in NJ. I'm in East Hanover. Very nice car, where did you find it?

[five0h2go]

Ron, I PM'd you. Thanks for the compliment!!!

[SVOhNo]

Heres a photochop of my car lookin about how I would like it. Lowered on a nice set of 10th anny wheels. Im lookin at these, cobras or even black bullits

http://img.photobucket.com/albums/v1...annywheels.jpg

Matt

[luvtolean]

Just a reminder....

When shopping for aftermarlet rims always always always get the inside bore diameter of the hub ( ie: hub spacing ) especially if you are going to use your stock brake rotors.

ALOT of aftermarlet rims will not fit. Now that doesnt mean you cant have the centers machined to fit, but if you do that take into consideration the center cap.

I believe the last time i checked the diam of the hub was something like 2.75in or 2.79 something like that.

Yep. 10th anniversaries will have to be machined to fit the stock front rotor. Trust me. My Cobra R's cleared though.

Also, I would put the wheels on before lowering. They're pretty wide, even with 245s rubbing is a concern in the rear without rolling any fenders.

[SVOhNo]

How hard would it be to roll the rear fender. Im wantin to get a nice mean stance with the SVO like my pic above and will do what it takes. I know I will prolly do the SN95 front swap, I found a few donor cars. What all should I take from them to make this work?
Matt